1Security Check

Before starting the installation, make sure your vehicle's battery is fully charged. Remove the negative (-) battery terminal and store it in a safe place.

2Required Tools

Prepare the following tools for installation:

• Phillips and flathead screwdriver set
• Cable crimpers and insulation tape
• Multimeter (for voltage check)
• Cable cutter and stripper
• Mounting adapters (depending on vehicle model)

1Front Panel Removal

Remove the front panel of the existing radio/CD player. Mounting screws are usually located on the sides or bottom.

2Removing Cable Connections

Carefully remove the antenna cable, power cable and speaker cables. Label each cable to note which connection it belongs to.

3Removing the Mounting Frame

Remove the mounting frame of the old system. Some vehicles may require special adapters.

1Mounting Location

Place the GL-300 system in your vehicle's DIN slot (standard 2-DIN or 1-DIN adapter). Select the mounting adapter according to your 9", 9.7" or 10" screen option.

• Remove the front panel and clean the DIN slot
• Place the mounting adapter into the DIN slot
• Secure the GL-300 unit to the adapter

2Cable Connections

Cable connections for GL-300:

• Power Cable: Connect Red (+12V), Black (GND), Yellow (ACC) cables
• Speaker Cables: Make 4-channel speaker connections (FL, FR, RL, RR)
• GPS Antenna: Connect GPS antenna cable and place antenna on top of vehicle
• USB Cable: Connect USB extension cable
• Rear View Camera (Optional): Connect RCA video cable and reverse signal

3First Boot and System Settings

GL-300 first boot settings:

• Turn on system and select language (Turkish)
• Configure Wi-Fi and Bluetooth connections
• Wait for GPS signal (5-10 minutes on first boot)
• Perform speaker test and optimize audio settings

1Mounting Location

Install GL-500 system as rear seat entertainment system:

• For headrest mounting: Determine 10.1" or 14" screen option
• For console multimedia mounting: Determine 9" or 10" screen option
• Secure mounting accessories to rear seat or console

2Cable Connections

Special connections for GL-500:

• HDMI Input/Output: Connect external devices by connecting HDMI cable
• Power Connection: Connect 12V power cable to vehicle battery
• Wi-Fi and Bluetooth: Place antennas for wireless connections
• Audio Output: Connect speaker or headphone output

3Testing and Verification

GL-500 system test:

• Check power connection and turn on system
• Test screen touch control
• Test HDMI connection (with external device)
• Verify Wi-Fi and Bluetooth connections

1Mounting Location

GL-700 premium system installation:

• Use special mounting adapter for 10.25" IPS screen
• Check vehicle-specific cables for OEM integration
• Place system in DIN slot and secure with screws

2Cable Connections

Advanced connections for GL-700:

• CAN-BUS Integration: Connect to vehicle CAN-BUS system (for steering wheel control)
• OEM Camera Connection: Connect vehicle OEM camera system
• Power and Speakers: Make standard power and speaker connections
• GPS and USB: Make GPS antenna and USB connections

3First Boot and System Settings

GL-700 initial setup:

• Turn on system and configure OEM integration settings
• Perform steering wheel control calibration
• Optimize camera image settings
• Configure and test audio system

1Mounting Location

Mount GV-F100 M01 camera to front windshield:

• Place camera on upper middle part of front windshield, behind rearview mirror
• Clean mounting adhesive and secure camera
• Adjust camera viewing angle (should face front windshield fully)

2Power Connection

Power connection:

• Vehicle Charger Adapter: Connect camera power cable to vehicle charger adapter
• Fuse Box Connection: Alternatively, you can get direct power from fuse box
• Battery Protection: Set battery protection level for parking mode (11.8V/12.0V/12.2V)

3G-Sensor and Parking Mode Settings

Camera settings:

• G-Sensor Sensitivity: Adjust G-sensor sensitivity for collision detection
• Parking Mode: Activate parking mode (time-lapse: 15min/12s/24s/48s)
• Voice Commands: Use record start, emergency video, time-lapse recording commands

4GoLook App Installation

Connection with mobile app:

• Download GoLook app to your phone (via QR code)
• Connect to camera Wi-Fi network
• View videos and configure settings

1Mounting Location

GV-F100 M02 installation (similar to M01, with 2K features):

• Mount to front windshield (same location as M01)
• Use sufficient memory card for 2K resolution (64GB recommended)

22K Image and WDR Settings

Advanced image settings:

• Resolution: Select 2K (2560×1440) resolution
• WDR (Wide Dynamic Range): Activate WDR feature (enhanced night performance)
• Night Vision: Optimize LED-supported night vision settings

3Testing and Verification

M02 system test:

• Record in 2K resolution and check image quality
• Test WDR feature in night and day
• Verify G-sensor and parking mode operation

1Mounting Location

GV-F100 M05 dual channel installation:

• Mount front camera to front windshield (4K resolution)
• Mount rear camera to rear windshield or trunk lid (1080p)
• Optimize viewing angle of both cameras

2Cable Connections

Dual channel connections:

• Front Camera: Connect 4K video cable and power cable
• Rear Camera: Connect 1080p video cable and power cable
• GPS Module: Activate built-in GPS module
• ADAS Connection: Make necessary connections for ADAS features

3ADAS and GPS Settings

Advanced features:

• ADAS Features: Activate lane tracking, close distance warning, collision prevention warnings
• GPS Location Tracking: Wait for GPS signal and verify location information
• Dual Channel Synchronization: Check that front and rear camera recordings are synchronized

1Mounting Location

DH-2 rear-view camera mounting:

• Mount camera to trunk lid, above or beside license plate
• Make mounting holes waterproof for IP67 water resistance
• Position camera properly for ~160° wide-angle view

2Cable Connections

DH-2 connections:

• Video Cable: Connect RCA video cable to multimedia system
• Power Cable: Connect 12V power cable to reverse light or directly to battery
• Reverse Signal: Connect reverse signal cable (for automatic activation)

3Image Settings

Camera image settings:

• Guide Lines: Turn guide lines on/off (from multimedia system)
• Image Mode: Select mirror/normal image mode
• Night Vision: Optimize LED-supported night vision settings

4Testing and Verification

DH-2 test procedure:

• Put in reverse gear and check camera image
• Verify viewing angle and image quality
• Check that guide lines work correctly
• Test night vision performance

1Mounting Location

DH-3 Sony sensor camera mounting:

• Same mounting location as DH-2 (trunk lid)
• Optimize viewing angle for Sony CMOS sensor advantages

2Sony CMOS Sensor Advantages

DH-3 special features:

• Enhanced Night Vision: Sony CMOS sensor provides superior night vision performance
• High Dynamic Range: Shows bright and dark areas balanced
• Fast Response: Fast image processing in low light conditions

3Cable Connections

DH-3 connections (same as DH-2):

• RCA video cable connection
• 12V power connection
• Reverse signal connection

1Mounting Location

DH-5 premium camera mounting:

• Use special mounting accessories for IP68 water resistance
• Make optimal positioning for Sony CCD sensor advantages

2Sony CCD Sensor and IP68 Features

DH-5 premium features:

• IP68 Water Resistance: Full water resistance, deep water immersion protection
• Sony CCD Sensor: Premium night vision and image quality
• Wide Temperature Range: -20°C ~ +70°C operating temperature

3Cable Connections

DH-5 connections:

• Standard RCA video and power connections
• Make cable entries waterproof for IP68 protection

1Mounting Location

MPA2240E 2-channel amplifier mounting:

• Mount amplifier to trunk or under trunk, leaving sufficient space for ventilation
• Ensure mounting surface is flat and clean
• Secure amplifier with screws (231×105×57 mm dimensions)

2Power Connection

Power connections:

• Positive (+12V): Connect directly to battery positive terminal with thick cable (at least 8 AWG)
• Negative (GND): Connect to vehicle chassis or battery negative terminal
• Remote (REM): Connect to multimedia system remote output (for on/off)
• Fuse: Place fuse box between battery and amplifier (30-40A recommended)

3Cable Connections

Audio connections:

• Input (RCA): Connect RCA cables from multimedia system (left and right channel)
• Output (Speaker): Connect speaker cables (2Ω, 4Ω or 8Ω impedance)
• Power Values: 2Ω: 2×240W, 4Ω: 2×150W, 8Ω: 2×120W (bridge mode: 4Ω: 1×500W, 8Ω: 1×300W)

4Testing and Verification

MPA2240E test procedure:

• Check power connections with multimeter (should be 12V)
• Turn on amplifier and check LED indicator
• Test at low volume level and check for distortion
• Check THD value (should be ≤0.15%)

1Mounting Location

MPD1100E monoblock amplifier mounting (for subwoofer):

• Mount as subwoofer amplifier to trunk or under trunk
• Leave space for sufficient ventilation

2Power Connection

MPD1100E power connections (similar to MPA2240E):

• Thick power cable (+12V), chassis connection (GND), remote connection
• Use thicker cable for high power (6 AWG recommended)

3Cable Connections

Subwoofer connections:

• RCA Input: Connect from multimedia system subwoofer output
• Subwoofer Output: Connect to subwoofer speaker
• Frequency Setting: Set low-pass filter (usually 80-120Hz)

1Mounting Location

CPA series amplifier mounting:

• Standard amplifier mounting procedure (trunk or under trunk)
• Leave sufficient space for ventilation and safety

2Power Connection

CPA series power connections:

• CPA8002D: 2-channel amp, CPA4320E: 4-channel amp
• Use appropriate cable thickness according to power requirements

3Cable Connections

Audio connections:

• CPA8002D: 2-channel RCA input, 2-channel speaker output
• CPA4320E: 4-channel RCA input, 4-channel speaker output

1Mounting Location

SRB series speaker mounting:

• Mount to front or rear door panel speaker slot
• Check existing speaker slot size (for 6.5" or 10")
• Secure speaker with screws and make sound insulation

2Cable Connections

Speaker connections:

• Positive (+) and Negative (-) Cables: Connect cables from amplifier or multimedia system with correct polarity
• Impedance Check: Check speaker impedance (usually 4Ω or 8Ω)
• Power Values: Select amplifier suitable for speaker power values

3Testing and Verification

Speaker test procedure:

• Test at low volume level
• Check that each speaker works
• Perform phase check (are positive/negative correctly connected?)
• Check for distortion

1Mounting Location

DTX series subwoofer mounting:

• Mount subwoofer to trunk or under trunk
• Leave sufficient space for ventilation
• Secure subwoofer box (enclosure) safely
• Different sizes: DTX460S, DTX680S, DTX810S, DTX1200S, DTX1001T, DTX480E

2Cable Connections

Subwoofer connections:

• Amplifier Connection: Connect from monoblock amplifier (like MPD1100E) to subwoofer with thick cable
• RCA Input: Connect RCA cable from multimedia system subwoofer output
• Power Connection: Power is taken from amplifier (subwoofer has no direct power connection)

3Frequency and Phase Settings

Subwoofer settings:

• Low-Pass Filter: Set low-pass filter on amplifier (usually 80-120Hz)
• Phase Setting: Set subwoofer phase (0° or 180°)
• Gain Setting: Set gain on amplifier (maximum sound without distortion)

4Testing and Verification

Subwoofer test procedure:

• Test with low-frequency music (bass test)
• Check for distortion
• Adjust balanced sound between subwoofer and speakers
• Optimize phase setting (for best bass response)

1Preparing the Mounting Adapter

Prepare the mounting adapter suitable for your vehicle model. The adapter will secure your Clarion system to your vehicle's DIN slot.

2Detailed Cable Connection Diagram

Connect your Clarion Android system cables carefully in the following order:

Power Cable Connection:

• Red Cable (+12V): Connect to the +12V line from the vehicle battery
• Black Cable (GND): Connect to the vehicle chassis or battery negative terminal
• Yellow Cable (ACC): Connect to the 12V line from the ignition switch
• Orange Cable (ILL): Connect to the lighting line (optional)

Antenna Cable Connection:

• Antenna Adapter: Connect the vehicle antenna cable to the Clarion antenna adapter
• Antenna Power Cable: Connect the antenna power cable to the +12V line
• Antenna Control Cable: Connect the antenna control cable to the system antenna output

Speaker Cable Connections:

• Front Left Speaker: White cable (+) and White-Black cable (-)
• Front Right Speaker: Gray cable (+) and Gray-Black cable (-)
• Rear Left Speaker: Green cable (+) and Green-Black cable (-)
• Rear Right Speaker: Purple cable (+) and Purple-Black cable (-)
• Subwoofer (If Available): Blue cable (+) and Blue-Black cable (-)

Rear View Camera Connection:

• Video Cable: Connect the camera video cable to the RCA socket
• Power Cable: Connect the camera power cable to the +12V line
• Control Cable: Connect the reverse gear signal cable

USB and External Connections:

• USB Cable: For USB memory or phone connection
• AUX Cable: For external audio input (optional)
• GPS Antenna Cable: Connect the GPS antenna cable for navigation

3Placing the System in the Slot

Place your Clarion system with the mounting adapter into the DIN slot and secure it with screws.

1First Boot and Android Startup

Reconnect the battery terminal and turn on the ignition. When your Clarion Android system boots up, follow these steps:

• Android Boot Screen: After the Clarion logo appears, the Android startup screen will appear
• First Setup Wizard: On the "Welcome" screen, tap the "Start" button
• Language Selection: Select the "Turkish" option and tap the "Next" button
• Region Selection: Select "Turkey" and tap the "Next" button

2Android System Settings

Make the following settings on the main screen:

• Settings Menu: Tap the "Settings" icon on the main screen
• System Settings: Tap the "System" option
• Date and Time: Tap the "Date and Time" option
• Time Zone: Select "GMT+3 (Istanbul)"
• Date Format: Select the "DD/MM/YYYY" format
• Time Format: Select the "24 hour" format

3Display Settings

For image quality:

• Display Settings: Go to "Settings" > "Display" menu
• Brightness: Set between 70-80%
• Auto Brightness: Set to "On" position
• Screen Timeout: Set to "30 seconds"
• Screen Orientation: Select "Auto"

4Audio System Settings

Test the speaker connections:

• Audio Settings: Go to "Settings" > "Sound" menu
• Main Volume: Set to 50%
• Fader: Set to "0" (center) position
• Balance: Set to "0" (center) position
• Bass: Set to "+2" level
• Treble: Set to "+1" level
• Speaker Test: Check each speaker by tapping the "Test" button

5Bluetooth Pairing

Pair your phone via Bluetooth:

• Bluetooth Menu: "Settings" > "Connections" > "Bluetooth"
• Turn On Bluetooth: Set the "Bluetooth" switch to "On" position
• Add Device: Tap the "Add Device" button
• Phone Settings: Open "Settings" > "Bluetooth" on your phone
• Device Search: Find the "Clarion" or "Android" device
• Pairing: Tap the device and confirm the pairing code
• Connection Test: Test by playing music from your phone

6Wi-Fi Connection

For internet connection:

• Wi-Fi Menu: "Settings" > "Connections" > "Wi-Fi"
• Turn On Wi-Fi: Set the "Wi-Fi" switch to "On" position
• Network Selection: Select your existing Wi-Fi network from the list
• Password Entry: Enter your Wi-Fi password
• Connection Test: Check for the "Connected" text

1GPS Antenna Installation

Place the GPS antenna on the top of your vehicle, away from metal obstacles. Connect the antenna cable to the Clarion system.

2Map Loading

Load navigation maps:

• Transfer map files to the system via USB memory
• Complete the map loading process
• Wait for GPS signal on first boot (5-10 minutes)

3Navigation Settings

Configure navigation settings:

• Select your preferred route type (fast/short/economic)
• Activate traffic warnings
• Save your favorite locations

1Common Issues

System Not Booting:

• Check power cable connections
• Check fuse status
• Measure battery voltage (should be 12V)

2Audio Issues

No Sound from Speakers:

• Check that speaker cables are connected correctly
• Check audio settings
• Check speaker impedance (4-8 ohm)

3Bluetooth Issues

Cannot Establish Bluetooth Connection:

• Check that your phone's Bluetooth is turned on
• Delete previous pairings and try again
• Check that the system is in Bluetooth mode

4Technical Support

You can get technical support for your issues:

• Phone: (0216) 232 45 38
• Email: info@clarionturkiye.com
• Working Hours: Monday-Friday 09:00-18:00